Epson Photo 1390 Adjustment Program

Here is the link for the properly labeled Epson Photo 1390. Just a correction to the file labeled CX1390.

Epson Photo 1390 Adjustment Program
http://www.mediafire.com/?gdtjykjm200

Epson C92/Photo R220/R230 Adjustment Program

Epson C92 Adjustment Program
http://www.mediafire.com/download.php?wuu2pn1tnkw

Epson Photo R220/R230 Adjustment Program with indoreset.bat
http://www.mediafire.com/download.php?9jbogzhk99v


Good luck to those who need these reseters!

Happy reseting to everyone.

HP 9000 Printers

1. Turn the printer off
2. Press and hold the
CHECK key
3. Power on the printer
4. Release the
CHECK key after all three lights come on The display should read SELECT LANGUAGE
5. Press the up arrow until
MAINTENANCE KIT is displayed, then press the CHECK key again and the maintenance kit count has been reset

HP 8000/8100/8150 Printers

Press the

MENU button until the display reads CONFIGURATION MENU

Press the

ITEM button until the display reads SERVICE MESSAGE = ON/OFF

Select

OFF*

Press

SELECT to save

Turn printer off

Hold the

VALUE MINUS and ITEM MINUS buttons while turning the printer back on Hold buttons down until display reads RESET MAINT/COUNTand

HP 4500/4550 Printers

1. Turn the printer off
2. Hold down the
CANCEL JOB and SELECT keys and turn the printer on, then wait until the display goes blank and the three LED's come on
3. Press the right side of the
MENU key, then press the SELECT key
4. You will enter
SERVICE MODE after the normal test completes
5. Press the
ITEM key until the FUSER MAINTENANCE COUNT appears
6. Press
VALUE +/- to change to zero
7. Press
SELECT to save
8. Press
GO; the printer should return to READY

HP 4000/4050/4100/5000 Printers:

1. Turn the printer off
2. Hold down the left side of the
ITEM and VALUE +/- keys, turn the printer on and wait
until RESET MAINTENANCE COUNT is displayed and then release the keys

HP IIISi Printers:

1. Press
ONLINE until the light goes off
2. Hold down
MENU until PCL CONFIG MENU appears
3. Press the
MENU key until SERVICE MSG=ON* appears
4. Press the
+ or - key to change display to SERVICE MSG=OFF
5. Press
ENTER/RESET MENU key to turn message off, the * should appear, then press ONLINE

Canon MP390

1)Printer on, press Additional Functions, Scan, Copy, Scan
Now you should be in service mode from there for waste ink tank reset it is simalar to what has already been posted

2)Select Test mode which is like the last avalabe selection
3)Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

The menu will now say EEPRON Clear
Select Ink count which is option (0) and press set

Then press Stop/Reset Followed by the power button and then wait for it to restart.

Canon MP160 , MP145 Error Codes

Error Code :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

Canon MPC190

Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan, Copy, Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Canon BJC-5000

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265 Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650

1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5 .Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME

How to Reset Canon BJC 1000 Series

1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon S200SPx

1. Without the cartridge installed and with the front cover closed, connect the AC cord
while holding down the RESET button.

2. Release the RESET button, press it down again within less than 5 sec and before the
cartridge carrier starts to move and make a sound (this is critical timing, if you hear the
printer, you are too late. Start again - they don't tell you this in tha manual, it is a
given)

3. Hold down the RESET button for 2 sec or more and realease it once again.

4. EEPROM reset - Quickly again and before the printer satrts to move and make more sounds,
hold down the RESET button for 2 secs or more and release it.

How to Reset Canon PIXMA iP1200, 1300, 1500, 1600, 1700, 1800

Canon PIXMA iP1200, 1300, 1500, 1600, 1700, 1800
Waste Ink Counter Reset.
Step 1: Manual for Service mode
Start with the printer OFF
1. Unplug power and USB.
2. Hold down POWER and plugin the cable power
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done blinking

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

How to Reset Canon PIXMA IP1000

Canon PIXMA iP1000
Waste Ink Counter Reset.
Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

How to Waste Ink Counter Reset Canon i320, i255

Canon i320, i255

Waste Ink Counter Reset.
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

HP Color LaserJet 4600 Printer (FUSER KIT RESET)

1. After Maintenance is performed, the display should read
NEW FUSER KIT =
2. Press the down arrow to highlight
YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW FUSER KIT and select

HP Color LaserJet 4600 Printer (IMAGE TRANSFER KIT (ETB) RESET)

1. After Maintenance is performed, the display should read
NEW TRANSFER KIT =
2. Press the down arrow to highlight
YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW TRANSFER KIT and select

HP Color LaserJet 4500/4550 Printers (TRANSFER KIT RESET)

1. Press the
MENU button until the RESETS MENU is displayed
2. Press the
ITEM button until TRANSFER KIT SELECT IF DONE is displayed
3. Press the
SELECT button

How to Reset Your Canon Pixma IP1880

Waste Ink Counter Reset Manual for Service mode
1. Turn On iP1880
2. Push and Hold Resume button about 2 minutes
3. Release Resume button
4. Printer back to normal again

Canon MP145 Resetter Program

If you’re having trouble with your printer that says Service Error 5001. This usually occurs when your canon printer has reach its maximum prints, it needs to be reset using a special program or do it manually.

You can find procedures or steps on how to reset your printer counter on many websites. Try using google to find those sites. Beware that resetting your printer might cause some sort of damage on the firmware and stop printer from functioning. Do it with your own risk. Good Luck!

With the printer powered off but connected to a power source , you must:

A) Press stop/reset button, and then press [ON/OFF] button to restart
B) Press [ON/OFF] again and then press twice the stop/reset button.
C) Press [ON/OFF] & Stop/reset button together, this time to enter the repair status and power lights will be green,
D) Press stop/reset button 4x and warning lights will be go out in [ON/OFF]button.
E) Turn off the printer.( it must be turn off) and then turn it on again.

Use with your own risk , i’ll try this way and m